Switching Options2017-06-30T16:50:50+00:00

Switching Options

symbol sensor

.PFX HF-SENSOR PREFIX

symbol spannung 230V 50-60Hzsymbol ta -20 +45

Application

Description

Typical Application

Sensor high frequency system 5,8GHz ISM frequency band, max. nominal load 800VA, 360° coverage, parameter preselection via DIP-switch, reach adjustable 2/4/6m, time adjustment 12Sec., 3/15/30Min., light-control settings ~10Lx/100Lx/500Lx/2000Lx, current drain Standby >0.9W, as Master with additionally switched exit clamp. Registered design protected by Deutsches Patent- und Markenamt No. 20 2010 011.944.8

Applicable in public areas such as corridors and stair cases, spottily used areas in interiors, as stand-alone or crosslinked in groups of luminaires in master/slave master/master configuration. Usage in exteriors possible dependent on local conditions.

Replacing an existing switched luminaire by a sensor-controlled luminaire grants the opportunity to adapt the switched on period to the effective requirements.

Additionally Required
---

Combination Opportunity
.BSR .TSR, .NSW .SAC .P15 .EBL .EBX .ZBL .USW

Symbol B2S

.BSR Bistable Switching

symbol spannung 230V 50-60Hz

Application

Description

Typical Application

Integrated option for switching of 2 operating modes via external switching (switch/key, motion sensor, photoelectric sensor, impulse time switch), suitable for switching of single circuits as well as functional options like .P15 or sensors according to requested operation.

Suitable for energetic optimization in existing buildings by functional adaption of luminaire operation where no wiring or radio is available for controlling.

For Luminaires with 2 or more circuits the option allows their switching in partial or full load in accordance to effective use without touching electrical wiring.

Additionally Required
---

Combination Opportunity
.PFX .NSW .P15 .EBL .EBX .ZBL .USW

Symbol B3S

.TSR Tristable Switching

symbol spannung 230V 50-60Hz

Application

Description

Typical Application

Integrated option for switching of 3 operating modes (A, B, AB) via external switching (switch/key, motion sensor, photoelectric sensor, impulse time switch), suitable for switching of single circuits as well as functional options like .P15 or sensors according to requested operation.

Suitable for energetic optimization in existing buildings by functional adaption of luminaire operation where no wiring or radio is available for controlling.

For Luminaires with 3 or more circuits the option allows their switching in partial or full load in accordance to effective use without touching electrical wiring.

Additionally Required
---

Combination Opportunity
.PFX .NSW .P15 .EBL .EBX .ZBL .USW

Symbol NSW

.NSW Int. Night Switch

symbol spannung 230V 50-60Hz

Application

Description

Typical Application

Sensor-controlled twilight switching with ON/OFF delay: 10 - 15s, adjustable: 2 - 300Lux, sensor element IP65 (IP degree of luminaire to be reduced in case), interior control IP20

Suitable for areas in which during daylight no artificial light is necessary but a constant operation during the night.

Illumination on building exteriors (e.g. house number illumination).

Additionally Required
---

Combination Opportunity
.PFX .P15 .EBL .EBX .ZBL .USW

Symbol SAC

.SAC Phase-Controlled Actuator

symbol spannung 230V 50-60Hzsymbol ta -20 +45

Application

Description

Typical Application

Integrated actuator with control over phase transited mains for switching of single luminaires or luminaire groups, even in different building sections or buildings. Controllable and addressable via central control unit.

Suitable for energetic optimization in existing buildings by functional adaption of luminaire operation where no wiring or radio is available for controlling.

Composition of luminaire groups and their switching by control modules in building areas which do not allow the installation of control wiring or radio control.

Additionally Required
--- (Control module S_LDSM1L-ST01-H02)

Combination Opportunity
.P15 .EBL .EBX .ZBL .USW

Symbol P15

.P15 Base Load Switching

Application

Description

Typical Application

Module for switching the luminaire base load of app. 15% via internally generated 1-10V-control voltage for the integrated pulse wide modulation, control by mains voltage switch (sensor, switch, night switch, impulse time switch).

Suitable for establishing a base/full load lighting where even during standby a base illumination is necessary.

Corridors or stair cases in nursing homes like retirement homes or hospitals.

Additionally Required
.DM_

Combination Opportunity
.BSR .PFX .EBL .EBX .ZBL .NSW